The Curt Harness for Your Tribute, part # C55255, is actually considerably longer than that. I had it measured in our warehouse and it's about 37 inches total. view full answer...
The overall length of the MB Sturgis hose you asked about is 24-7/8 inches so it's too short for you.
Instead I recommend using part # 37207-30645 which is 30 inches. It's a little longer than what you need but it has the same fittings. view full answer...
Anytime a hitch extender like the MaxxTow Dual Hitch Extender is used it reduces the weight capacity of the trailer hitch it's installed into by 50%. The only way you can safely use it to the full capacity is if your trailer hitch is rated for 8,000 lbs towing and 800 lbs tongue.
Since the hitch on your motorhome is rated at 5K that means when using this extender that is reduced to 2,500 lbs towing/250 lbs tongue.
The safest solution that we have to offer is to use the Gen-Y Adjustable... view full answer...
When installing the # 9465-56 Hide-A-Goose hitch in your 2016 GMC Sierra 2500HD short bed, a hole must be drilled in the bed of the truck. Mark and drill a 1/4” hole 44-7/8 inches from the rear of the bed forward centered between the two wheel wells.
A hole saw will be used to enlarge the hole to the proper size. I attached an install video that shows how this hitch would be installed in a similar 2015 Chevy Silverado 2500HD as yours. view full answer...
The Gen-Y Hitch Shock Absorbing 5th Wheel Pin Box part # 325-GH-8040 will have dimensions similar to the Lippert Trailair RotoFlex so you should not have an issue with the trailer not being level if you did not before. That said, I have attached a photo with the dimensions of the pin box for you if you want to confirm beforehand.
If the trailer was nose high after installing the pin box and making your adjustments, there is always the option to raise the trailer like with the Dexter Trailer... view full answer...
Yes having the rear jacks of the Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System w Touchpad and Remote # LC675817 24 inches from the rear axle would be totally fine. view full answer...
I may have a solution for you, but the top of the box of the UWS Truck Bed Fender Well Toolbox with Drawers - Passenger's Side - 3.9 cu ft - Bright Aluminum # UWS01625 sits 4" above truck bed rails, so it will not work with a tonneau cover. Instead, you could use the UWS Truck Bed Chest - Secure Lock Under Tonneau Series - 8.85 cu ft - Bright Aluminum # UWS08297 which is designed to fit underneath a tonneau cover and provides you with a locking storage solution. It's quite a bit bigger... view full answer...
The distance between the two arms that form the "V" shape at the widest point is 46-3/4". See the diagram below which shows all of the dimensions for the bike rack. view full answer...
The distance from the end of the spindle to the face of the brake flange on the #84 E-Z Lube Spindle w/ Brake Flange # TRU74FR is 5-3/8". See the diagram below which shows this measurement. view full answer...
A tire like the Karrier ST205/75R14 Radial Trailer Tire - Load Range D # AM10235 can fit a variety of different wheel widths so it is not possible to determine the width from just the tire. This tire size fits 14" x 5", 14" x 5-1/2", 14" x 6", and 14" x 6-1/2" wheels.
Most wheels will have their size stamped on the back side so I would start by checking there to see if you can find the width. If you are unable to locate this you will have to measure. To find the width of a trailer wheel... view full answer...
The Rhino-Rack SUP and Surfboard Pads # RRRWP03 have a foam piece that is 42mm thick which is about 1.65" so these will be a little bit under what you're looking for.
For your application I recommend using something like the Malone Deluxe Kayak Carrier with Tie-Downs # MPG152 instead. These foam blocks measure 3" tall in the center of the block so they will give you the height you're needing.
Attached are some review videos for you to check out. view full answer...
The Wesbar Submersible Low Profile Trailer Light, # 403026, uses bolts that require a 1/4 inch diameter hole to mount. The distance between the mounting holes is 4 inches on center and the bolts are 1 inch long. view full answer...
Thanks so much for drawing that to our attention! The weight of the Furrion 2-in-1 Range Oven with Glass Cover - 21" Tall - Stainless Steel # FR97KR is 72 pounds. view full answer...
While we have an alternative, the part number you asked about has been discontinued. But what you can use is the Trailer Wiring Junction Box # 3375601100 and Hopkins 7-Way RV Style Connector - 8' Long # H20046.
This 7-way uses 14 gauge wires for the red, brown, green, and yellow; 12 gauge for the blue; and 10 gauge for the white and black wires. view full answer...
I reached out to Dexter and they recommend using 20-30 ft lbs of torque for the Replacement Oil Cap Kit for AL-KO and Hayes 10,000-lb to 16,000-lb Axles # K71-859-00. view full answer...
The Reese Sidewinder 5th Wheel King Pin with Rotating Turret - Lippert 1716 - 20,000lbs # RP77FR turret has an outside edge to outside edge measurement of 11.875" and the included spacer kit has two spacers that are approximately 1/4" thick. view full answer...
The maximum speed recommended by tire chain manufacturers can vary from one chain to the next. Usually rated between 25 to 30 mph.
However, your MVP owners manual specifies not driving over 19 mph when using chains. Always go by the lower rating and make sure to drive safely in hazardous conditions. I have included a link to our FAQ article on tire chains for you. view full answer...
I pulled the Dexter Electric Trailer Brake Assembly, # 23-451, from my warehouse and found that it weighs 17.9 lbs. The shipping weight, which includes the packaging is approximately 23 lbs. view full answer...